If the holes don’t bother you, you can leave them there just in case you decide that you want to put the original vintage tuners back on. Since you have to screw the new pegs into a different area of the head-stock, there will be screw holes from the old tuning pegs that are exposed. As a result, you are probably going to have to re-drill to accommodate for the new mounting tabs. When switching between the modern sealed gear tuners, the mounting tabs are never alike, even within the same brand. These reamers are tapered tools that cut through the wood to gradually enlarge the holes. The biggest modification you are going to have to make in order for the modern tuners to fit, is to enlarge the peg hole diameter. If you don’t care about the value going down on the guitar, and are determined to put modern sealed gear tuners on your guitar, then continue with the following paragraphs to find out what have to do. If all possible, try to replace them with the exact match so your guitar can keep the value it deserves. The overall value of the guitar will go down. Just so you know, there is a caveat to replacing vintage tuners with modern tuners. If you decide that you want to switch your vintage tuning pegs to modern ones, you will have to make some modifications to your guitar. Guitar Tuning Peg Replacement Changing From Vintage To Modern Tuners As a result, these modern duplicates require peg holes with a larger diameter in order for them to fit in the head-stock of the guitar. If you look on modern duplicate housing, the casting has a larger diameter than the vintage tuner. There are modern tuners that replicate the original vintage tuner, but how are you supposed to be able to tell the difference? You can also check the peg-hole on the head-stock because sealed gear tuners are usually installed into a peg hole that is 3/8″ of an inch diameter, or slightly more, considering the brand. The best way to spot them is to inspect the tuner and confirm that it has a 10 mm bushing that is threaded with a washer around it. You can easily identify sealed tuners because each brand looks closely related. Sealed Gear tuning machines have a housing over the worm gear to keep dirt out, and also to keep them permanently lubricated. Most of the time they are installed into a peg hole that has a 1/4” inch diameter that has been enlarged slightly on the peg head face (around 11/32”) so the bushing can fit. These bushings (as the name suggests) are pressed into the tuning peg holes on the head-stock, and are held in by resistance. Another way to identify them is look for a bushing that is “press fit”. If the tuners on your guitar have an open gear, they are usually vintage. Once you have found out what style of tuning pegs are on your guitar, you need to identify what type you have. 3 x 3 tuners are the type that have three on one side of the headstock, then three on the other side ( Ex. Inline tuners are the type that are all on one side of the head-stock of the guitar ( Ex. Does My Guitar Have Inline or 3 x 3 TunersĬheck to see if your guitar has inline or 3 x 3 tuners. If it seems like you’ve looked everywhere, contacted the manufacturer and for some odd reason you can’t get any information, you can try taking the next step. They might even be able to sell you a set directly from the phone. They should be able to give you the specs that you need. If it’s not that obvious online you can actually contact the manufacturer of your guitar and give them the serial number that’s on the back of the head-stock. You can usually find a replacement set for your guitar online by searching the tuners by the brand of the guitar itself. The first thing to do when trying to find the right tuning pegs for your guitar is to find an exact match for your guitar type. Continue reading on to find out! What Tuners Fit My Guitar? Where To Start First So, what CAN you do to be able to get a new set of tuners on your guitar. It would be awesome if tuning pegs were a “one size fits all”, but unfortunately this is not the case. Unless you are changing to a set of tuning pegs that have exactly the same specifications as the set that is currently on the guitar, some modifications will have to be done to the guitar to be able to install the new set of tuning pegs. As a result, they need to be replaced, but can you replace them with any type of tuning peg? I decided to do some research and find out if tuning pegs for guitar are universal, or if not, what would I need to do to replace them? Tuning pegs, like all other parts of the guitar get old and even break.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |